mirror of
https://github.com/Klipper3d/klipper.git
synced 2025-10-31 02:15:52 +01:00
c7330e07a4
* Copyright in log.c * GPIO check completely removed * generic/timer_irq added * Change in doc section Signed-off-by: Eugene Krashtan <eug.krashtan@gmail.com>
143 lines
4.0 KiB
Markdown
143 lines
4.0 KiB
Markdown
This document describes how the STM32F0 port operates and how to work with
|
||
tiny CAN-enabled boards.
|
||
|
||
Required components
|
||
===================
|
||
|
||
#### MCP2515 module
|
||
|
||
|
||
or this
|
||
|
||
|
||
#### St-link dongle
|
||
|
||
|
||
|
||
|
||
Adding CAN bus to Raspberry Pi
|
||
==============================
|
||
(Based on Quick Guide https://www.raspberrypi.org/forums/viewtopic.php?f=44&t=141052)
|
||
|
||
First of all, (only if you have small CAN module) it’s necessary to modify the CAN-module from ebay, because it has
|
||
only one VCC pin, but the MCP2515 needs to be powered from 3V3 and the TJA1050
|
||
CAN-transceiver needs to be powered from 5V. Powering both chips from 5V would
|
||
work, but then a level-shifter for the SPI would be needed. The Pi's GPIO pins
|
||
are NOT 5V tolerant. Cut a trace on the PCB and soldered a pin onto the trace
|
||
to deliver 5V only to the TJA1050. Be sure to cut the trace before the capacitor:
|
||
|
||
|
||
|
||
Next connect the module:
|
||
|
||
| MCP2515 | Raspberry Pi |
|
||
| --- | --- |
|
||
| VCC | 1 (3V3) |
|
||
| TJA 1050 VCC | 2 (5V) |
|
||
| GND | 6 (GND) |
|
||
| CS | 24 (CE0) |
|
||
| MISO | 21 (MISO) |
|
||
| MOSI | 19 (MOSI) |
|
||
| SCK | 23 (SCK) |
|
||
| INT | 22 (GPIO25) |
|
||
|
||
Install can-utils:
|
||
> sudo apt-get install can-utils
|
||
|
||
To activate the driver for the MCP2515 you have to add a kernel overlay, to do
|
||
so edit the /boot/config.txt
|
||
> sudo nano /boot/config.txt
|
||
|
||
And add the following lines (set oscillator value according to crystal on your board):
|
||
|
||
```
|
||
dtparam=spi=on
|
||
dtoverlay=mcp2515-can0,oscillator=8000000,interrupt=25
|
||
dtoverlay=spi1-1cs
|
||
```
|
||
|
||
Now reboot, after the reboot try to setup the the can interface:
|
||
> sudo ip link set can0 up type can bitrate 500000
|
||
|
||
If no errors occurred, the can interface should be ready now.
|
||
To make the CAN-interface permanent, add the following lines to /etc/network/interfaces
|
||
|
||
```
|
||
auto can0
|
||
iface can0 can static
|
||
bitrate 500000
|
||
```
|
||
|
||
Communicating over CAN
|
||
======================
|
||
|
||
Use "Serial over CAN" emulator software to establish connection:
|
||
https://github.com/Delsian/CanSerial
|
||
|
||
Install st-link on Raspberry Pi
|
||
===============================
|
||
|
||
> sudo apt-get update
|
||
|
||
> sudo apt-get install cmake
|
||
|
||
> sudo apt-get install libusb-1.0-0-dev
|
||
|
||
> git clone https://github.com/texane/stlink stlink-repo
|
||
|
||
> cd stlink-repo
|
||
|
||
> make
|
||
|
||
> cd build/Release/
|
||
|
||
> sudo make install
|
||
|
||
|
||
Copy to /etc/udev/rules.d/49-stlinkv2.rules:
|
||
|
||
```
|
||
# stm32 discovery boards, with onboard st/linkv2
|
||
# ie, STM32L, STM32F4.
|
||
# STM32VL has st/linkv1, which is quite different
|
||
|
||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="3748", \
|
||
MODE:="0666", \
|
||
SYMLINK+="stlinkv2_%n"
|
||
|
||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="374b", \
|
||
KERNEL!="sd*", KERNEL!="sg*", KERNEL!="tty*", SUBSYSTEM!="bsg", \
|
||
MODE:="0666", \
|
||
SYMLINK+="stlinkv2_%n"
|
||
|
||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="374b", \
|
||
KERNEL=="sd*", MODE:="0666", \
|
||
SYMLINK+="stlinkv2_disk"
|
||
|
||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="374b", \
|
||
KERNEL=="sg*", MODE:="0666", \
|
||
SYMLINK+="stlinkv2_raw_scsi"
|
||
|
||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="374b", \
|
||
SUBSYSTEM=="bsg", MODE:="0666", \
|
||
SYMLINK+="stlinkv2_block_scsi"
|
||
|
||
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0483", ATTRS{idProduct}=="374b", \
|
||
KERNEL=="tty*", MODE:="0666", \
|
||
SYMLINK+="stlinkv2_console"
|
||
|
||
# If you share your linux system with other users, or just don't like the
|
||
# idea of write permission for everybody, you can replace MODE:="0666" with
|
||
# OWNER:="yourusername" to create the device owned by you, or with
|
||
# GROUP:="somegroupname" and control access using standard unix groups.
|
||
```
|
||
|
||
Now "make flash" command can upload HEX into connected board
|
||
|
||
Pins allocation
|
||
===============
|
||
|
||
Configurations with CAN and Serial port uses different pins, and during enumeration
|
||
process firmware reports all possible pin names. But actually you can use only
|
||
existing pins, not involved in communication. Wrong pins will generate shutdown.
|