prind/config/printer-simulavr.cfg

# This file contains example pin mappings for testing with the
# "simulavr" program. To use this config, compile the firmware for an
# AVR atmega644p, enable "low-level configuration options", and enable
# "simulavr software emulation". Further details are in
# docs/Debugging.md.

# See docs/Config_Reference.md for a description of parameters.

[stepper_x]
# Pins: PA5, PA4, PA1
step_pin: PA5
dir_pin: PA4
enable_pin: PA1
microsteps: 16
rotation_distance: 40
endstop_pin: ^PB0
position_min: -0.25
position_endstop: 0
position_max: 200

[stepper_y]
# Pins: PA3, PA2
step_pin: PA3
dir_pin: PA2
enable_pin: PA1
microsteps: 16
rotation_distance: 40
endstop_pin: ^PB1
position_min: -0.25
position_endstop: 0
position_max: 200

[stepper_z]
# Pins: PC7, PC6
step_pin: PC7
dir_pin: PC6
enable_pin: PA1
microsteps: 16
rotation_distance: 8
endstop_pin: ^PB2
position_min: 0.1
position_endstop: 0.5
position_max: 200

[extruder]
# Pins: PC3, PC2
step_pin: PC3
dir_pin: PC2
enable_pin: PA1
microsteps: 16
rotation_distance: 33.500
nozzle_diameter: 0.500
filament_diameter: 3.500
heater_pin: PB4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA7
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
min_extrude_temp: 0
max_temp: 210

[heater_bed]
heater_pin: PB3
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PA0
control: watermark
min_temp: 0
max_temp: 110

[fan]
pin: PD6

[mcu]
serial: /opt/printer_data/run/simulavr.tty

[printer]
kinematics: cartesian
max_velocity: 500
max_accel: 3000
max_z_velocity: 25
max_z_accel: 30


## vvv Required by Moonraker/Mainsail/Fluidd vvv
[virtual_sdcard]
path: /opt/printer_data/gcodes

[display_status]

[pause_resume]

[gcode_macro PAUSE]
description: Pause the actual running print
rename_existing: PAUSE_BASE
# change this if you need more or less extrusion
variable_extrude: 1.0
gcode:
  ##### read E from pause macro #####
  {% set E = printer["gcode_macro PAUSE"].extrude|float %}
  ##### set park positon for x and y #####
  # default is your max posion from your printer.cfg
  {% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
  {% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
  ##### calculate save lift position #####
  {% set max_z = printer.toolhead.axis_maximum.z|float %}
  {% set act_z = printer.toolhead.position.z|float %}
  {% if act_z < (max_z - 2.0) %}
      {% set z_safe = 2.0 %}
  {% else %}
      {% set z_safe = max_z - act_z %}
  {% endif %}
  ##### end of definitions #####
  PAUSE_BASE
  G91
  {% if printer.extruder.can_extrude|lower == 'true' %}
    G1 E-{E} F2100
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}
  {% if "xyz" in printer.toolhead.homed_axes %}
    G1 Z{z_safe} F900
    G90
    G1 X{x_park} Y{y_park} F6000
  {% else %}
    {action_respond_info("Printer not homed")}
  {% endif %}

[gcode_macro RESUME]
description: Resume the actual running print
rename_existing: RESUME_BASE
gcode:
  ##### read E from pause macro #####
  {% set E = printer["gcode_macro PAUSE"].extrude|float %}
  #### get VELOCITY parameter if specified ####
  {% if 'VELOCITY' in params|upper %}
    {% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
  {%else %}
    {% set get_params = "" %}
  {% endif %}
  ##### end of definitions #####
  {% if printer.extruder.can_extrude|lower == 'true' %}
    G91
    G1 E{E} F2100
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}  
  RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
gcode:
  TURN_OFF_HEATERS
  CANCEL_PRINT_BASE