mirror of
				https://github.com/Klipper3d/klipper.git
				synced 2025-10-31 10:25:57 +01:00 
			
		
		
		
	config: Skr mini e3 v1.2 template (#2069)
Signed-off-by: Eelco Pandelaar <epandi@gmail.com>
This commit is contained in:
		
							
								
								
									
										121
									
								
								config/generic-bigtreetech-skr-mini-e3-v1.2.cfg
									
									
									
									
									
										Normal file
									
								
							
							
						
						
									
										121
									
								
								config/generic-bigtreetech-skr-mini-e3-v1.2.cfg
									
									
									
									
									
										Normal file
									
								
							| @@ -0,0 +1,121 @@ | ||||
| # This file contains common pin mappings for the BIGTREETECH SKR mini | ||||
| # E3 v1.2. To use this config, the firmware should be compiled for the | ||||
| # STM32F103 with a "28KiB bootloader". Also, select "Enable extra | ||||
| # low-level configuration options" and configure "GPIO pins to set at | ||||
| # micro-controller startup" to "!PC13". | ||||
|  | ||||
| # The "make flash" command does not work on the SKR mini E3. Instead, | ||||
| # after running "make", copy the generated "out/klipper.bin" file to a | ||||
| # file named "firmware.bin" on an SD card and then restart the SKR | ||||
| # mini E3 with that SD card. | ||||
|  | ||||
| # See the example.cfg file for a description of available parameters. | ||||
|  | ||||
| [stepper_x] | ||||
| step_pin: PB13 | ||||
| dir_pin: !PB12 | ||||
| enable_pin: !PB14 | ||||
| step_distance: .0125 | ||||
| endstop_pin: ^PC0 | ||||
| position_endstop: 0 | ||||
| position_max: 235 | ||||
| homing_speed: 50 | ||||
|  | ||||
| [tmc2209 stepper_x] | ||||
| uart_pin: PB15 | ||||
| microsteps: 16 | ||||
| run_current: 0.580 | ||||
| hold_current: 0.500 | ||||
| stealthchop_threshold: 250 | ||||
|  | ||||
| [stepper_y] | ||||
| step_pin: PB10 | ||||
| dir_pin: !PB2 | ||||
| enable_pin: !PB11 | ||||
| step_distance: .0125 | ||||
| endstop_pin: ^PC1 | ||||
| position_endstop: 0 | ||||
| position_max: 235 | ||||
| homing_speed: 50 | ||||
|  | ||||
| [tmc2209 stepper_y] | ||||
| uart_pin: PC6 | ||||
| microsteps: 16 | ||||
| run_current: 0.580 | ||||
| hold_current: 0.500 | ||||
| stealthchop_threshold: 250 | ||||
|  | ||||
| [stepper_z] | ||||
| step_pin: PB0 | ||||
| dir_pin: PC5 | ||||
| enable_pin: !PB1 | ||||
| step_distance: .0025 | ||||
| endstop_pin: ^PC2 | ||||
| position_endstop: 0.0 | ||||
| position_max: 250 | ||||
|  | ||||
| [tmc2209 stepper_z] | ||||
| uart_pin: PC10 | ||||
| microsteps: 16 | ||||
| run_current: 0.580 | ||||
| hold_current: 0.500 | ||||
| stealthchop_threshold: 5 | ||||
|  | ||||
| [extruder] | ||||
| step_pin: PB3 | ||||
| dir_pin: !PB4 | ||||
| enable_pin: !PD2 | ||||
| step_distance: 0.010526 | ||||
| nozzle_diameter: 0.400 | ||||
| filament_diameter: 1.750 | ||||
| heater_pin: PC8 | ||||
| sensor_type: EPCOS 100K B57560G104F | ||||
| sensor_pin: PA0 | ||||
| control: pid | ||||
| pid_Kp: 21.527 | ||||
| pid_Ki: 1.063 | ||||
| pid_Kd: 108.982 | ||||
| min_temp: 0 | ||||
| max_temp: 250 | ||||
|  | ||||
| [tmc2209 extruder] | ||||
| uart_pin: PC11 | ||||
| microsteps: 16 | ||||
| run_current: 0.650 | ||||
| hold_current: 0.500 | ||||
| stealthchop_threshold: 5 | ||||
|  | ||||
| [heater_bed] | ||||
| heater_pin: PC9 | ||||
| sensor_type: ATC Semitec 104GT-2 | ||||
| sensor_pin: PC3 | ||||
| control: pid | ||||
| pid_Kp: 54.027 | ||||
| pid_Ki: 0.770 | ||||
| pid_Kd: 948.182 | ||||
| min_temp: 0 | ||||
| max_temp: 130 | ||||
|  | ||||
| [fan] | ||||
| pin: PA8 | ||||
|  | ||||
| [mcu] | ||||
| serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00 | ||||
|  | ||||
| [printer] | ||||
| kinematics: cartesian | ||||
| max_velocity: 300 | ||||
| max_accel: 3000 | ||||
| max_z_velocity: 5 | ||||
| max_z_accel: 100 | ||||
|  | ||||
| [static_digital_output usb_pullup_enable] | ||||
| pins: !PC13 | ||||
|  | ||||
| [board_pins] | ||||
| aliases: | ||||
|     # EXP1 header | ||||
|     EXP1_1=PB5, EXP1_3=PA9,   EXP1_5=PA10, EXP1_7=PB8, EXP1_9=<GND>, | ||||
|     EXP1_2=PB6, EXP1_4=<RST>, EXP1_6=PB9,  EXP1_8=PB7, EXP1_10=<5V> | ||||
|  | ||||
| # See the sample-lcd.cfg file for definitions of common LCD displays. | ||||
		Reference in New Issue
	
	Block a user