mirror of
				https://github.com/Klipper3d/klipper.git
				synced 2025-10-31 10:25:57 +01:00 
			
		
		
		
	config: Add config for printer Creality CR10s Pro V2 (#6300)
Created a base config for the Creality CR10s Pro v2 as described here: https://www.creality.com/products/cr-10s-pro-v2-3d-printer This will allow users with this printer to more easily setup Klipper firmware. Signed-off-by: Peter Kydas <peter@kydas.me>
This commit is contained in:
		
							
								
								
									
										154
									
								
								config/printer-creality-cr10s-pro-v2-2020.cfg
									
									
									
									
									
										Normal file
									
								
							
							
						
						
									
										154
									
								
								config/printer-creality-cr10s-pro-v2-2020.cfg
									
									
									
									
									
										Normal file
									
								
							| @@ -0,0 +1,154 @@ | ||||
| # This file contains pin mappings for the Creality CR-10S Pro V2. To use | ||||
| # this config, the firmware should be compiled for the AVR atmega2560. | ||||
|  | ||||
| # See docs/Config_Reference.md for a description of parameters. | ||||
|  | ||||
| ## General Config | ||||
| [mcu] | ||||
| serial: /dev/serial/by-id/<YOUR_USB_ID> | ||||
|  | ||||
| [printer] | ||||
| kinematics: cartesian | ||||
| max_velocity: 200 | ||||
| max_accel: 1500 | ||||
| max_z_velocity: 10 | ||||
| max_z_accel: 100 | ||||
|  | ||||
| ## Stepper Motors and Extruder | ||||
| [stepper_x] | ||||
| step_pin: PF0 #ar54 | ||||
| dir_pin: PF1 #ar55 | ||||
| enable_pin: !PD7 #!ar38 | ||||
| rotation_distance: 40 | ||||
| microsteps: 16 | ||||
| full_steps_per_rotation: 200 | ||||
| endstop_pin: ^PE5 #^ar3 | ||||
| position_endstop: 0 | ||||
| position_min: 0 | ||||
| position_max: 300 | ||||
| homing_speed: 50 | ||||
| homing_retract_dist: 5 | ||||
|  | ||||
| [stepper_y] | ||||
| step_pin: PF6 #ar60 | ||||
| dir_pin: !PF7 #ar61 | ||||
| enable_pin: !PF2 #!ar56 | ||||
| rotation_distance: 40 | ||||
| microsteps: 16 | ||||
| full_steps_per_rotation: 200 | ||||
| endstop_pin: ^PJ1 #^ar14 | ||||
| position_endstop: 0 | ||||
| position_min: 0 | ||||
| position_max: 310 | ||||
| homing_speed: 50 | ||||
| homing_retract_dist: 5 | ||||
|  | ||||
| [stepper_z] | ||||
| step_pin: PL3 #ar46 | ||||
| dir_pin: !PL1 #!ar48 | ||||
| enable_pin: !PK0 #!ar62 | ||||
| rotation_distance: 8 | ||||
| microsteps: 16 | ||||
| full_steps_per_rotation: 200 | ||||
| endstop_pin: probe:z_virtual_endstop | ||||
| position_min: -3 | ||||
| position_max: 363 # you can go higher but then the cables crimp | ||||
|  | ||||
| [extruder] | ||||
| step_pin: PA4 # ar26 | ||||
| dir_pin: PA6 # !ar28 | ||||
| enable_pin: !PA2 # !ar24 | ||||
| rotation_distance: 22.900 | ||||
| microsteps: 16 | ||||
| full_steps_per_rotation: 200 | ||||
| nozzle_diameter: 0.400 | ||||
| filament_diameter: 1.750 | ||||
| max_extrude_only_distance: 500.0 | ||||
| max_extrude_only_velocity: 70.0 | ||||
| max_extrude_only_accel: 1000.0 | ||||
| heater_pin: PB4 #ar10 | ||||
| sensor_type: EPCOS 100K B57560G104F | ||||
| sensor_pin: PK5 #analog13 | ||||
| control: pid #calibrated in Klipper, you will need to run this for your machine | ||||
| pid_kp: 28.359 | ||||
| pid_ki: 1.616 | ||||
| pid_kd: 124.426 | ||||
| min_extrude_temp: 170 | ||||
| min_temp: 5 | ||||
| max_temp: 275 | ||||
|  | ||||
| [fan] | ||||
| pin: PH6 #ar9 | ||||
|  | ||||
| [heater_bed] | ||||
| heater_pin: PH5 #ar8 | ||||
| sensor_type: EPCOS 100K B57560G104F | ||||
| sensor_pin: PK6 #analog14 | ||||
| control: pid #calibrated in Klipper, you will need to run this for your machine | ||||
| pid_kp: 70.936 | ||||
| pid_ki: 1.151 | ||||
| pid_kd: 1093.298 | ||||
| min_temp: 5 | ||||
| max_temp: 140 | ||||
|  | ||||
| ## BLTouch and Safe Z Settings | ||||
| [bltouch] | ||||
| sensor_pin: ^PD2 | ||||
| control_pin: PB5 | ||||
| stow_on_each_sample: False # Be careful | ||||
| probe_with_touch_mode: True | ||||
| x_offset: -27 | ||||
| y_offset: -2 | ||||
| z_offset: 2 # you will need to calibrate this in Klipper | ||||
| speed: 4.0 | ||||
| samples: 2 | ||||
| sample_retract_dist: 3.0 | ||||
|  | ||||
| [safe_z_home] | ||||
| home_xy_position: 177,155 | ||||
| speed: 80.0 | ||||
| z_hop: 10.0 | ||||
| z_hop_speed: 5.0 | ||||
|  | ||||
| [bed_mesh] | ||||
| speed: 120 | ||||
| horizontal_move_z: 5 | ||||
| mesh_min: 5, 5 | ||||
| mesh_max: 268, 305 | ||||
| probe_count: 5,5 | ||||
| fade_start: 1 | ||||
| fade_end: 10 | ||||
|  | ||||
| [filament_switch_sensor e0_sensor] | ||||
| switch_pin: PE4 #ar2 | ||||
| pause_on_runout: False | ||||
| runout_gcode: | ||||
|   PAUSE_PARK | ||||
|  | ||||
| ## Calibrating the Bed | ||||
| # this is for the bltouch to calibrate the bed | ||||
| [screws_tilt_adjust] | ||||
| screw1: 40,40 | ||||
| screw1_name: front left screw | ||||
| screw2: 295,40 | ||||
| screw2_name: front right screw | ||||
| screw3: 295,280 | ||||
| screw3_name: rear right screw | ||||
| screw4: 40,280 | ||||
| screw4_name: rear left screw | ||||
| speed: 50 | ||||
| horizontal_move_z: 10 | ||||
| screw_thread: CW-M3 | ||||
|  | ||||
| [bed_screws] | ||||
| screw1: 13,38 | ||||
| screw1_name: front left screw | ||||
| screw2: 268,38 | ||||
| screw2_name: front right screw | ||||
| screw3: 268,278 | ||||
| screw3_name: rear right screw | ||||
| screw4: 13,38 | ||||
| screw4_name: rear left screw | ||||
| horizontal_move_z: 5 | ||||
|  | ||||
| [pause_resume] | ||||
| @@ -34,6 +34,7 @@ CONFIG ../../config/printer-bq-hephestos-2014.cfg | ||||
| CONFIG ../../config/printer-creality-cr5pro-ht-2022.cfg | ||||
| CONFIG ../../config/printer-creality-cr10-v3-2020.cfg | ||||
| CONFIG ../../config/printer-creality-cr10s-2017.cfg | ||||
| CONFIG ../../config/printer-creality-cr10s-pro-v2-2020.cfg | ||||
| CONFIG ../../config/printer-creality-cr20-2018.cfg | ||||
| CONFIG ../../config/printer-creality-cr20-pro-2019.cfg | ||||
| CONFIG ../../config/printer-creality-ender5plus-2019.cfg | ||||
|   | ||||
		Reference in New Issue
	
	Block a user