kiauh/scripts/functions.sh

# setting up some frequently used functions
check_euid(){
  if [ "$EUID" -eq 0 ]
  then
    echo -e "${red}"
    echo -e "/=================================================\ "
    echo -e "|    !!! THIS SCRIPT MUST NOT RAN AS ROOT !!!     |"
    echo -e "\=================================================/ "
    echo -e "${default}"
    exit 1
  fi
}

source_ini(){
  source ${HOME}/kiauh/kiauh.ini
}

start_klipper(){
  if [ -e /etc/init.d/klipper ]; then
    status_msg "Starting klipper service ..."
    sudo /etc/init.d/klipper start && sleep 2 && ok_msg "Klipper service started!"
  fi
}

stop_klipper(){
  if [ -e /etc/init.d/klipper ]; then
    status_msg "Stopping klipper service ..."
    sudo /etc/init.d/klipper stop && sleep 2 && ok_msg "Klipper service stopped!"
  fi
}

restart_klipper(){
  if [ -e /etc/init.d/klipper ]; then
    status_msg "Restarting klipper service ..."
    sudo /etc/init.d/klipper restart && sleep 2 && ok_msg "Klipper service restarted!"
  fi
}

start_moonraker(){
  if [ -e /etc/init.d/moonraker ]; then
    status_msg "Starting moonraker service ..."
    sudo /etc/init.d/moonraker start && sleep 2 && ok_msg "Moonraker service started!"
  fi
}

stop_moonraker(){
  if [ -e /etc/init.d/moonraker ]; then
    status_msg "Stopping moonraker service ..."
    sudo /etc/init.d/moonraker stop && sleep 2 && ok_msg "Moonraker service stopped!"
  fi
}

restart_moonraker(){
  if [ -e /etc/init.d/moonraker ]; then
    status_msg "Restarting moonraker service ..."
    sudo /etc/init.d/moonraker restart && sleep 2 && ok_msg "Moonraker service restarted!"
  fi
}

dep_check(){
  for package in "${dep[@]}"
  do
    ! command -v $package >&/dev/null 2>&1 && install+=($package)
  done
  if ! [ ${#install[@]} -eq 0 ]; then
  warn_msg "The following packages are missing but necessary:"
  echo ${install[@]}
  while true; do
    read -p "Do you want to install them now? (Y/n): " yn
    case "$yn" in
      Y|y|Yes|yes|"")
      status_msg "Installing dependencies ..."
      sudo apt-get install ${install[@]} -y && ok_msg "Dependencies installed!"
      break;;
      N|n|No|no) break;;
         *) echo "Unknown parameter: $yn"; echo;;
    esac
  done
  fi
}

print_error(){
  for data in "${data_arr[@]}"
  do
    if [ ! -e $data ]; then
      data_count+=(0)
    else
      data_count+=(1)
    fi
  done
  sum=$(IFS=+; echo "$((${data_count[*]}))")
  if [ $sum -eq 0 ]; then
    ERROR_MSG=" Looks like $1 was already removed!\n Skipping..."
  else
    ERROR_MSG=""
  fi
}

pkg_check(){
  status_msg "Checking if nginx is installed"
  if [[ $(dpkg-query -f'${Status}' --show nginx 2>/dev/null) = *\ installed ]]; then
echo "nginx found!"
else
echo "nginx was not found, installing..." 2>&1
sudo apt-get -y install nginx 2>/dev/null
fi
}

build_fw(){
    if [ -d $KLIPPER_DIR ]; then
      cd $KLIPPER_DIR && make menuconfig
      status_msg "Building firmware ..."
      make clean && make && ok_msg "Firmware built!"
    else
      warn_msg "Can not build firmware without a Klipper directory!"
    fi
}

### grab the printers id
get_usb_id(){
  warn_msg "Make sure your printer is the only USB device connected!"
  while true; do
    echo -e "${cyan}"
    read -p "###### Press any key to continue ... " yn
    echo -e "${default}"
    case "$yn" in
      *) break;;
    esac
  done
  status_msg "Identifying the correct USB port ..."
  USB_ID=$(ls /dev/serial/by-id/*)
  if [ -e /dev/serial/by-id/* ]; then
    status_msg "The ID of your printer is:"
    title_msg "$USB_ID"
  else
    warn_msg "Could not retrieve ID!"
    return 1
  fi
}

write_printer_id(){
  while true; do
    echo -e "${cyan}"
    read -p "###### Do you want to write the ID to your printer.cfg? (Y/n): " yn
    echo -e "${default}"
    case "$yn" in
      Y|y|Yes|yes|"")
        backup_printer_cfg
cat <<PRINTERID >> $PRINTER_CFG

##########################
### CREATED WITH KIAUH ###
##########################
[mcu]
serial: $USB_ID
##########################
##########################
PRINTERID
        ok_msg "Config written!"
        break;;
      N|n|No|no) break;;
    esac
  done
}

flash_routine(){
  echo -e "/=================================================\ "
  echo -e "|                   ATTENTION!                    |"
  echo -e "| Flashing a Smoothie based board for the first   |"
  echo -e "| time with this script will certainly fail.      |"
  echo -e "| This applies to boards like the BTT SKR V1.3 or |"
  echo -e "| the newer SKR V1.4 (Turbo). You have to copy    |"
  echo -e "| the firmware file to the microSD card manually  |"
  echo -e "| and rename it to 'firmware.bin'.                |"
  echo -e "|                                                 |"
  echo -e "| You find the file in: ~/klipper/out/klipper.bin |"
  echo -e "\=================================================/ "
  echo
  while true; do
    echo -e "${cyan}"
    read -p "###### Do you want to continue? (Y/n): " yn
    echo -e "${default}"
    case "$yn" in
      Y|y|Yes|yes|"")
      get_usb_id && flash_mcu && write_printer_id; break;;
      N|n|No|no) break;;
    esac
  done
}

flash_mcu(){
  stop_klipper
  if ! make flash FLASH_DEVICE="$USB_ID" ; then
    warn_msg "Flashing failed!"
    warn_msg "Please read the log above!"
  else
    ok_msg "Flashing successfull!"
  fi
  start_klipper
}